Instrukcja montażu i obsługi, gwarancja Bosch Wtg86400sa

Subskrybuj nasze sieci społecznościowe, aby być na bieżąco z najnowszymi aktualizacjami!

Komentarz

Where do you get the schematics from? Thanks for another great video.

I'm proud your experienced to troubleshoots a dead motherboard. That's the most underrated and comprehensive boardview of that moboard component part operations video tutorial ever so far. But I need help a quick question my friend about my Asus P4P800-E Deluxe motherboard. This is my first time trying to resurrect/repair my dead motherboard. Only certain part I repaired and changed/replaced already the (1) BIOS chip, (2) capacitors, (1) IC-driver controller to mosfet, and (2) transistor mosfets (negative side body) near side of the CPU processor. I have the PTi9 LCD PCI Diagnostic Analyzer Tester...indicates LED lights of +12V, +5V, +3.3V, and Reset are good (lights on) & fan runs means no problem on transistor Mosfets anymore as I double tested too that 12Volts are running good designed to run CPU processor. But the PTi9 LCD PCI Diagnostic Analyzer tester still telling me that there's signal error, it says check the CPU and power box (power supply is tested good all +12V, -12V, +5V & +3.3V) and the other two indicates that RST and FRAME are both Invalid shows in PTi9 tester. Also I'm seeing LED lights of FRAME, IRDY, and SYSClk are off, it shows in the PTi9 PCI Diagnostic Analyzer tester. I have the "Boardviewer" software (to see the schematic diagram of P4P800-E Deluxe board) that I clicked the CPU drawing part and looked at the RESET, looked at the motherboard then tested the Resistor that is soldered/connected on negative side that the value is correct that has no problem. The two pin reset (for the button reset) doesn't work when I pressed the button. If you have time, please try to look on the Boardview in part of the RESET pin because it's not working. I don't know about that FRAME & RST where to troubleshoot that. I touched the CPU processor it doesn't make any at least build up heat/warm. I tested the CPU processor from my other Asus motherboard, it's running fine. What part of the motherboard should I trouble shoot on that P4P800-E Deluxe? This part I'm lost already. I need help, any idea? Great help would be appreciated so much.

Man your instructions is the best, I always watch videos on YouTube but your ones is easyier to understand and adapt.

what is the function of the mosfet, which is located above the processor socket and near the 16-volt capacitor? On my board, 12 volts come to this mosfet, and zero volts on its other two legs. on the next mosfet on all three legs, too, at zero volts. The multimeter does not detect a short circuit or a break on the 12 volt MOSFET. What could be the reason?

great work...thank you..we are waiting for another videos

It would be great to see one video where CPU pass the step but get MEMORY error even if the memory is OK.

So much more some information,is great

where can i get the schematics or board view of dell OptiPlex models, please tell me if u know something, I'm struggling here

thanks sir very much

Hi sir

good job

Bro ic near to the charging connecter in motherboard and heated but doesnt power on laptop , please help me bro

like this video.. thanks

hi dr-bios. i have asrock z87 pro3. suddenly dead, while watching youtube.

hangi ayağın nereye gittiğini gösteren anakart programı ücretsiz mi? nereden indirebiliriz?

hi sir. How to get board viwe file

It is cheaper to buy a new motherboard than to have it made

I have a problem. screen's lock. I forgot my mobile code Can you unlock iPhone X Max?

What about a board where no power indications come on at all. I checked the PSU and put a new 3.0V battery which are fine. The previous battery was drained. I have checked all over the internet and have no answers (The board has two leds and a built in power button all of which do not light up or work). Please help. Board is gigabyte z87x-ud5h

Thank you for the video. Where can I download the board view?

.

Zostaw komentarz

#0